About the Rockford Fosgate Prime R1000-1D
Now you can get Rockford Fosgate performance at value prices. Prime Series amplifiers bring out your music's subtle details as they drive your speakers with the clean power you need to overcome road noise and fill your car with sound.
Rockford Fosgate designed Prime amps to deliver Power Output Without Excessive Regulation (POWER), which means they'll respond quickly to the peak demands that you may throw at your system. Your driver's seat will become your favorite place for listening when you add the clarity and impact of a Prime amp.
The R1000-1D mono amp powers your subwoofers with up to 1,000 watts RMS so you will be feeling the bass. Use the low-pass filter and Rockford Fosgate's famous Punch bass boost to adjust the amp to work best with your enclosure and vehicle. A phase switch gets your subs to work together with the rest of your car's audio system for maximum impact. The included wired remote lets you control the amp's volume level from the front seat.
- mono subwoofer amplifier
- 500 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms)
- CEA-2006 compliant
- variable low-pass filter filter (40-130 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- wired remote Punch Level Control included
- Class-D amplifier design
- frequency response: 20-130 Hz
- MOSFET power and output stages
- preamp-level inputs and outputs
- 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- fuse rating: 30A x 3
- 12-1/8"W x 2-7/16"H x 7-11/16"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # R1000-1D
What's in the box:
- Mono-channel subwoofer amplifier with three 30-amp fuses installed in chassis
- 3 Additional 30-amp fuses
- Punch Level Control module
- 16.5' Punch Level Control cable terminated by a male 3.5mm connector on each end
- Mounting bracket
- 2 Small mounting screws
- 4 Large mounting screws
- 4 Flat washers
- Installation/Operation Manual (Eng/Spa/Fre)
- Amplifier Verification Certificate
Rockford Fosgate Prime R1000-1D reviews
Thanks for submitting your review
More details on the Rockford Fosgate Prime R1000-1D
Features & specs
|RMS Power Output (Watts x Channels)||
500 x 1 |
|Peak Power Output (Watts x Channels)||N/A|
|Power at 2 Ohms (Watts x Channels)||1000 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||2|
|Best Frequency Response||20-130Hz Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||85 dB|
|Low-Pass Crossover Frequency||40-130 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0-12 dB|
|Bass Boost Frequency||45 Hz|
|Speaker Level Inputs||No|
|Preamp Outputs||1 pair|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Overview: The Rockford Fosgate R1000-1D Prime 500 watt mono-channel amplifier is designed to power one or two subwoofers. The R1000-1D is designed with specific features to power your subwoofers with a frequency range between 20-130 Hz. This amplifier is not designed to power a full-range speaker.
Class-D: The Rockford Fosgate R1000-1D's high efficiency Class-D amplifier design reduces current consumption from your vehicle's charging system.
MOSFET Power: The Rockford R1000-1D is equipped with a MOSFET power supply and output stage for good sound, efficiency and dependability.
CEA 2006 Compliant: The Rockford Fosgate R1000-1D Prime's power ratings are measured according to the strict standards dictated by the Consumer Electronics Association (CEA). These standards allow you to accurately compare the rated power output of all CEA 2006-compliant amplifiers, even if they come from different brands. Manufacturers who adhere to the standards can display the CEA 2006 logo on their products and packaging.
- 4-Ohm Mono: 500 watts RMS x 1-channel in 4-ohm @ 20-130Hz with 1% THD
- 2-Ohm Mono: 1000 watts RMS x 1-channel in 2-ohm @ 20-130Hz with 1% THD
LED Indicators: The Rockford Fosgate amplifier is equipped with two side-mounted LED indicators.
- Power LED: This LED illuminates green when the unit is turned on.
- Protect LED: This LED illuminates red if a short circuit or too low of an impedance is detected at the speaker connections. The amplifier will automatically shut don if this occurs.
Mounting: The amplifier can be mounted vertically or horizontally using the supplied mounting screws. The amplifier should never be mounted upside down or in an engine compartment (this will void your warranty).
Gain Control: The amplifier's gain control is preset to match the output of most source units. The gain control can be adjusted from 150mV to 8V.
Low-Pass Crossover: The amplifier features a built-in 12dB/octave Butterworth low-pass filter with a crossover point variable from 40 to 130Hz.
Phase: The phase switch allows you to select the output phase of the amplifier between 0-degrees and 180-degrees to match the rest of your vehicle's speaker system.
Punch Bass: This is a Punch bass control on the amplifier that is adjustable up to 12dB at a fixed 45Hz.
Remote Punch Level Control: When the wired remote Punch Level Control is connected to the R1000-1D, the gain control of the amplifier is linked and allows you to remotely control the output level of the amplifier from the dash or center console of your vehicle. The wired remote Punch Level Control module features a rotary dial and comes supplied with mounting hardware and a 16.5' connector cable.
Power Terminals: The power and ground terminals are nickel-plated screw terminals and will accommodate up to 4 AWG power/ground wire (up to 1/2" spade or ring-style connector).
Remote Turn-On Terminal: The remote turn-on terminal is a nickel-plated screw terminal that will accommodate up to an 8 AWG wire (up 3/8" spade or ring-style connector). This terminal is used to remotely turn-on and turn-off the amplifier when +12V DC is applied, when connected to your headunit's remote turn-on lead. .
Speaker Terminals: The amplifier is equipped with two pairs of speaker terminals for an easy parallel subwoofer connection. The four speaker terminals (left +/- and right +/-) are heavy duty, nickel-plated screw-terminals what will accommodate up to 8 AWG speaker wire (up to 3/8" spade or ring-style connectors).
RCA Input Jacks: The industry standard RCA jacks provide an easy connection for signal level input. They are nickel-plated to resist signal degradation caused by corrosion.
RCA Output Jacks: This pair of RCA pass-thru jacks provide a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cable from the front of your vehicle to the rear amplifier location. They are nickel-plated to resist signal degradation caused by corrosion.
Punch Level Control: 3.5mm input for connecting the supplied Punch Level Control module.
Fuse: The amplifier is equipped with three installed 30-amp ATC fuses. The amplifier also comes supplied with three spare 30-amp fuses.
The Rockford Fosgate Prime R1000-1D replaces these items